Reviews (6)
()
PRODUCTS
![]()
![]()
![]()
Power Tools
Power Drill
Electric Trimmer
Electric Wrench
Electric Screwdriver
Spray Gun
Electric Scissors
Electric Saw
Electric Polisher
Heat Gun
Glue Gun
Other Power Tools
VIEW MORE
Hand Tools
EDC Gadgets
Screwdrivers
Cutters
Clamping Tools & Bench Vises
Abrasive Tools
Hammers
Wrenches
Scissors
Tools Kit
Other Hand Tools
VIEW MORE
Measurement Instruments
Nature Element Measurements
Laser Rangefinders
Digital Microscope
Borescope
Battery Testers
Measuring & Gauging Tools
Multimeters
Temperature Measurements
Weighing Scales
Thermal Imager
Other Instruments
VIEW MORE
2-in-1 Grafting Tools Pruner Kit
SKU：
Get notified when it's back in stock!
QTY:
-
+
In stock
Max per order : 50
Product details
FAQ
2-in-1 Grafting Tools Pruner Kit
INTRODUCTION
This grafting tool clones your favorite fruit tree over and over again. It is similar to transplanting organs in humans, you can combine parts from two different trees to form a single, functioning individual. It is most suitable for stocks from 1/6 to 1/2 inch in diameter. It makes a clean and neat cut in one stock and a corresponding cut in the other.
FEATURE
★ Professional Accessories
The versatile grafting tool performs three types of grafts (V-graft, Ω-graft & U-graft) as well as branch trimming.2 piece grafting tape for wrapping plants to prevent air ingress; The high-quality packaging design meets all your grafting needs at once.
★ High Survival Rate
Razor-sharp grafting blades(3 types of grafts plus 3 replacement blades) won’t crush softer scions and it will increase the survival rate.
★ Replaceable Grafting Blades
The grafting kit can handle both scion and rootstock 1/6 ”- 1/2 ” in diameter perfectly. Blades are consumables and regular maintenance is needed.
★ Easy to Use
The new professional-grade grafting tool with the trimmer is very easy to use and perfect cuts every time you use it. It is suitable for a variety of plants, especially fruit trees. We recommend that the blade be lubricated after each use to extend its life.
SPECIFICATION
| Type | Scissors |
| Material | SK5(double-edged cutting blades) Steel and ABS(handle) |
| Paraffin grafting tape | 1” wide |
| Dimension | 25*13*5cm |
| Weight | 800g |
How Budding Works
T-bud - Carve the bud out of the tree. Make sure you cut deep enough to expose the green layer below the bark; The cut should extend to about three-quarters of an inch above the bud.
Choose a good spot on the host tree. Ideally, you want to graft to a branch – or sapling – that’s between a quarter and one inch in diameter, and find a place as far from any existing buds as possible. If necessary trim away any buds within six to eight inches of the graft site.
Make a vertical cut about an inch long where you want to place the bud. At the top of it make a horizontal cut a third of the way around the branch or trunk – you’ve created your T. Now carefully use the knife to lift the bark on either side of the T’s stem, slip the scion into the cut. Use tape or rubber budding strips for this, being careful not to disturb the scion.
Chip bud – Cut a scion in the same way, but instead of making a T cut slice away a section of the host’s bark about the same size as the scion – the closer to matching the size, the better. Notch the bottom of it so the transplanted bud with be held in place, then fit the scion into the cut and trim until the green areas of both are as well-matched as possible. Bind with tape or rubber.
WHAT'S IN THE BOX
1 x 2-in-1 Grafting Tool
1 x Wrench
1 x Screwdriver
1 x Black storage case
3 x Replacement grafting blades
1 x Grafting knife
2 x Grafting tapes
ORDERING TIPS
* The combined shipping cost will be calculated automatically by the system after you choose the shipping destination in the checkout step.
* As the manufacturer needs the serial number to provide a replacement, we highly recommend you keep the original packing box or take picture of the code before discarding it. Thank you!
4.67
out of 5
5
4
3
2
1
Submitted successfully, we will follow up in time
Recommend
you have already liked
